Contents
The P728C Garage Door Spring GarageDoorSalesNearme.Com | The P728C garage door spring is a standard, plug-end type used in hardware assemblies for garage doors.
Two springs of this type support weights of up to 75 pounds, while two P528C springs support up to 105 pounds and two P328C springs can support weights of up to 250 pounds.
When buying a new spring, consider the size of the spring that is required, and the type of hardware that will be used to replace it.
The P728C Garage Door Spring
Color-Coded Torsion Springs
Color-coded garage door springs are the easiest way to determine if your garage doors are functioning properly. The chart will also show the diameter of the wires in the torsion springs, the wind direction, and the length of the entire torsion spring.
To check if you’re buying the right type of torsion spring for your garage door, use the chart to find out what size to order.
When you’re shopping for new extension springs for your garage door, you’ll likely notice the color-coded designation.
Different spring manufacturers will use a different color code to indicate their specific weights. In addition, different manufacturers may use different color-coding systems to indicate the strength of each spring.
Therefore, it’s important to weight the garage door before you purchase extension springs. However, it’s still a good idea to weigh it first to ensure that it’s the right spring for your door.
Garage doors are equipped with torsion springs to lift and lower them. These springs store electricity when the door is at rest. When it’s time to unlock or close the door, the springs release energy.
The color-coded springs on garage doors can make it easier to determine which spring is needed. If you have an existing garage door, you can purchase one with a color-coded spring that corresponds with its weight.
To replace the springs in your garage door, first take out the torsion tube and the spring. It’s important to note that the two torsion tubes are made of different materials, so make sure you have the right type of spring for your garage door.
To determine which springs should be replaced, measure their diameters. Afterwards, measure the length and inside diameter of the torsion spring.
The best time to replace the torsion springs on your garage door is about 7 years after installation. These torsion springs should be replaced every seven years, but you can still save money by replacing them early.
If you have not yet done so, you can also purchase new ones online. There are many hardware stores and even some online retailers that carry the exact spring you need. Additionally, professional garage door repair companies will know which ones to sell to you.
Extension Springs
If you’re planning to replace the extension springs in your garage door, you need to check which hardware assembly you’re replacing.
If you’re replacing the springs in your garage door, you’ll need to make sure that you get the right type of connector and plug end.
Usually, two P728C springs can support between 90 and 150 pounds each. Similarly, two P528C springs can support between 105 and 175 pounds each. Finally, you can choose from a range of P528C and P328C springs.
You can replace your extension springs in different heights by purchasing a new cable for the right length. When you replace your old springs, it is best to make sure that the new ones have the same length and pull as the old ones.
Otherwise, the old springs may not fit the new springs. When you replace the extension springs, you must make sure that you buy the right length for your door.
If you’re replacing your extension springs in your garage door, you need to measure the length of the broken spring. To do this, you need to take it out and compress it.
Alternatively, you can insert a shaft in the middle of the spring and count the number of coils. If the springs are damaged or missing, you’ll need to count them to make sure you get the right length.
Luckily, the door industry has standardized the length of the extension springs and there’s a spring length for almost any height of garage door.
The distance between the spring ends is its outside diameter. When measuring the spring, be sure to measure the length from the outside diameter to the center.
The spring’s inside diameter should be measured to the nearest one-eighth-inch. Using a micrometer can yield inaccurate measurements and may even break, so it’s best to use a caliper instead. If you measure with the wrong tool, you’ll end up with a spring that’s too short.
One-piece garage doors are also made with extension springs. These are the ones that hold the door up. If you’re using an extension spring for your door, you must make sure that both sides of the garage door have the same length.
Remember to keep the length of your extension spring in mind – it will not balance the door if one side is longer than the other.
In addition, be sure to check the color code of the extension springs. This makes it easier to identify replacement springs when you’re replacing the ones in your door.
P728C Garage Door Spring
Torsion Springs
The first thing you need to determine is whether or not your door is a torsion spring. You can purchase compatible springs by referencing your garage door’s weight, height, cable drum number, and track radius.
Torsion springs are rated for a certain number of cycles, each corresponding to a single cycle of the door opening and closing.
This rating does not take into account premature breakage, which is caused by steel chips and corrosive environments.
Taking measurements for a broken spring is simple. First, measure the inside diameter of the spring by dividing the distance by the number of coils.
Then, use a tape measure to measure each half. This measurement is critical because even a small error in measurement can cause the spring to be incorrectly sized.
To make sure you purchase the right size, you should check the inside diameter of the spring to ensure it is the correct size.
Torsion springs have a shaft with a special cone on one end. They connect to an idler bracket, which serves as a spring anchor bracket. Torsion springs usually have a conical end, which is screwed into the shaft.
Some springs have a special loop on the end, and others are secured to the barrel with a rod. The shaft is made of steel and is usually fixed to the wall or other fixed structure.
Extension springs have sheaves and other parts, which make them difficult to maintain and lubricate. Torsion springs are easier to lubricate and maintain compared to extension springs.
A broken garage door spring can also cause the door to slam unexpectedly, causing serious injury to a person standing close to it or damaging the door. So, make sure you have springs installed before the garage door is replaced.
Most doors have the same cycle life rating, but you should check the P728c garage door manufacturer’s website to make sure the model you have is torsion-compatible.
In the case of broken springs, you should change both of them. A single broken spring will most likely break again before you notice a problem. If you have two doors, replacing one of them will save you time in your garage and save you money in shipping costs.
Torquemaster Springs
The Wayne Dalton garage door torquemaster spring system uses 10,000 cycle replacement springs. Some weight selections of these springs may not fit into the original style.
In that case, you may have to convert your garage door to the Torquemaster plus spring system. If that’s the case, you can purchase a conversion kit to do it yourself. If the original style springs are beyond your budget, you may want to purchase a new one.
To replace a TorqueMaster garage door spring, first unwind the old spring and line up the spring’s end bracket with the marked area on the end bracket. Then, loosen the lock nut that secures the spring in place.
Then, use a 7/16″ nut driver or hex-head socket in a drill to unlock the gearbox winding bolt head. Turn the counter assembly until it approaches the “0” tick mark on the end bracket.
A TorqueMaster spring is made of steel, but the material is irrelevant as long as it is round at the end. The new spring can be replaced in either direction – the left or right wind.
Wayne Dalton provides two different winders, a left-wind spring and a right-wind spring. These garage door springs are designed to be a replacement for the old spring and help you maintain the balance of your garage door.
The TorqueMaster Plus system comes with a safety device that prevents you from accidentally dropping the tool while winding the springs.
This device also has an anti-drop safety device that locks the cable drum if the spring breaks. In addition, the TorqueMaster Plus system comes with a lock-out lever. If you accidentally drop the tool, you won’t be able to open your garage.