Contents
Garage Door That Won’t Go Down Unless I Hold the Button GarageDoorSalesNearme.Com | If you have a garage door that won’t go down unless you hold down the button to open it, there’s a possibility that something is wrong.
Misaligned safety eyes, worn out photo eyes, or old and rusted rollers could all be to blame. Here are some possible fixes to this problem. If you’re still unsure of the cause, read on to learn how to solve your issue.
Garage Door That Won’t Go Down Unless I Hold the Button
#Misaligned safety eyes
If you find yourself holding the button on your garage door and it won’t go down, it may be due to misaligned safety eyes.
Safety sensors should be at least six inches off the ground, but they are sometimes misaligned. The sending sensor should have a solid green light, while the receiving one will flash if a hand passes in front of it.
To fix this problem, check the wiring and sensors. Check the safety eyes by pulling the two wires from the sensor housings.
You may find that one of the wires is missing or the other is misaligned. If this is the case, you can disconnect and reconnect them. Alternatively, you can replace the safety eyes with a new one.
If the photo-eyes are misaligned, you may need to contact a repair service. You can also try unplugging the power supply to the garage door and see if that works.
If this does not work, try holding the button for about five seconds, then press the button again. This should clear the issue. If the misalignment is the problem, you may have a damaged photo-eye component.
Some garage doors have safety eyes that have misaligned. It is important to keep in mind that misaligned safety eyes can interfere with its ability to detect objects and people.
If the safety eyes fail to detect objects, you should contact the manufacturer to replace them. You can also ask a friend or neighbor if they have a similar problem.
#Misaligned door tracks
If your garage door will not go down unless you hold down the button, then it may be due to misaligned tracks. While the door may still move, it may slow down when it hits a certain spot or make rubbing noises. A garage door service specialist can safely realign the door and install new tracks. For more tips and advice, read on!
The first step is to check the photo eyes to see if they are functioning properly. If not, then it is probably time to call a professional.
The second step is to check the track alignment. A misaligned track is difficult to close or open, as it will not be able to register the other sensor.
Measure the height of each sensor’s eye from the floor. A laser level is a good tool for this task. You can purchase one at Home Depot for as little as $15.
Next, check the safety sensors. If these sensors are not functioning properly, the garage door may be malfunctioning. This can be a sign of misalignment or a blocked photo eye.
The photo eyes are two sensors that line up about four feet above the ground and send a pea-sized beam when activated.
When these sensors are misaligned, they will send a signal to the safety system to let it know that something is blocking the path.
The next problem may be the sensors themselves. If they aren’t properly aligned, the door won’t go down. Check the tracks for debris and clean them if necessary.
If you can’t find a problem with the sensors, then your door may be misaligned. A misaligned garage door may also be the culprit.
Garage Door Won’t Go Down Unless I Hold the Button
#Misaligned photo eyes
A misaligned photo eye on a garage door may be to blame. These safety sensors are made up of two pieces that align across the garage door and send a pea-sized laser beam when activated.
When one of the photo eyes becomes misaligned, the door will not open or close. The solution is to have the photo eyes aligned or remove the obstruction.
Another possible cause for misaligned photo eyes is dirt on the lens of the door. Like camera lenses, the photo eyes on a garage door are very small and easily get dirty.
Clean the photo eyes using a mild cleaner and avoid rubbing them with abrasive material. If the problem persists, call a repairman to perform the work for you.
You can try blocking the beam with a cardboard box. This will block the beam between the photo eyes. If the beam is blocked, the door will not go down.
Try using a non-corrosive material such as aluminum foil or a wood block to clear the obstruction. Then, you can test the photo eyes by pushing the button again. The door should go down after that.
A garage door that won’t close properly may have misaligned photo eyes. It may have recently been replaced with a new torsion spring.
This can cause the photo eyes to become misaligned, rendering them useless in scanning the clearance. Another cause is a problem with the balance between the door and the motor. The overly strong down force can put undue strain on the nylon drive gear.
#Old and rusted rollers
If your garage door won’t open or close fully, you may need to replace the rollers. The rollers can become damaged over time and will not work properly. You can remedy this problem by lubricating or replacing them.
If you’ve tried these methods, but they’re still not working, contact a garage door technician. If you’re unable to find an appropriate repair, contact a garage door company or a hardware store.
Rust penetrant is effective for loosening binders. Apply a drop of the liquid on the screw head, and then spread it down the threads. Repeat as necessary.
If the binders still won’t loosen, try lubricating them. You can also try using a hammer to remove them. Make sure to wear leather gloves when you do this.
Garage Door Won’t Go Down Unless I Hold the Button
#Electrical connections
Your garage door opener may be experiencing trouble when the electrical connections are loose. There are two possibilities: one of the wires is damaged, while the other may be plugged in but not working properly.
If this happens, the opener may not function at all. To fix the problem, you can either disconnect the wiring and reconnect it at the opener or replace the entire door unit. If you have a manual door opener, follow the steps below to diagnose the problem.
If the door has a manual opener, the problem may be related to the electrical connections. Over time, the wires may begin to corrode. The corroded connections can cause the door to fail to close.
To fix this problem, remove the wire plugs from the opener and wipe or blow off the ends. Then, re-insert the wires into the sensor. This fix is not a sure fire solution, however.
